New Cattle/Livestock Trailer - 2022 EBY Maverick LS 6'6" X 16' X 7'

Description

• 2022 EBY MAVERICK LS BH1MLS 6'6" W X 16' L X 7' T. BUMPER PULL STOCK TRAILER.  
• 2 5200 LB TORSION BRAKE AXLES, 235/85/R 16 10 PLY RADIAL TIRES ON 8 LUG 16" WHEELS, EXTRUDED ROLLED ALUMINUM FENDERS, LED LIGHTS WITH LED BACK UP LIGHT IN TAIL LIGHT, SPARE TIRE, CENTER GATE, 
• STOCK # 2031119
• This is the equivalent of a 14k Trailer with lower ratings Primarily for Licensing purposes. 

Floor Length:  16’

Outside Width:  6’5”

Inside Height:  7'

Running Gear: Standard Features

• 16' Model
  • GVWR: 10,000lbs.
  • Axles:  (2) 5,200# rubber ride (greased packed bearings), 96” wide
  • Wheels:  16” x 6” heavy duty steel, 8-lug
  • Tires:  (4) ST235/85R16 steel belted radials, load range E
  • Brakes: 12” x 2” electric on both axles – 16’.
• Safety Equip.:  Two chains and electronic breakaway kit.
• Landing Gear:  Single speed top-wind crank.
• Coupler:  2-5/16” ball coupler (12,500# rating).

Box Construction:

• Front Nose: Tapered V-nose with .080 aluminum smooth sheets and vertical hat posts. (3) Cast
• Assembly:  aluminum corner caps and extruded radius front corner posts.
• Slats:  Standard exterior slat spacing.  Pattern A on all 6’6”  trailers and pattern B on all 7’ inside height trailers.  8” openings are notched for optional closures.
• Posts:  Extruded aluminum, 1” x 3” tapered tubular side posts, spaced on 18” centers maximum.
• Bottom Rails:  12” extruded aluminum.
• Top Rails:  6” extruded aluminum.
• Crossmembers:  3” extruded aluminum J-beams on 12” centers.
• Floor:  .125 flat aluminum diamond plate.
• Side Door:  29” wide, curb side, 10-3/4” from drop sheet.
• Rear Frame Assembly:  3” x 5” tubular extruded aluminum with Eby cast aluminum corner caps.
• Rear Door:  Full swing with (2) 4” extruded aluminum offset hinges for extended swing radius.  Hinges are mechanically fastened and welded to rear frame.  30” wide exterior sliding door on roadside with polyurethane rollers at the top and UHMW wear pads at the threshold.

Roof Assembly:

• Sheet:  One-piece .040 aluminum externally riveted to top rail on 4” centers.
• Bows:  Arched, hat shaped 1-1/2” x 4” extruded aluminum on 24” centers.

Partitions:

• Std. Partition:  Extruded aluminum tube and punched sheet construction with outside release slam latch.  Extruded aluminum pipe hinge with nylon bushing mounted curbside. Partition located on post nearest centerline of box.

Lights & Wiring (Meets all US and Canadian Regulations.)

• Lights:  12-volt D.O.T. approved, LED.
• Wiring:  A.T.A. color coded, wiring harness.
• Rear Lights:  Modular, turn-tail-stop, LED.  One light each side (red).
• Inside Lights:  One sealed beam, with external rear water resistant switch.

Miscellaneous:

• Tire Carrier:  None standard – Added only with spare wheel and tire option, mounted on exterior front sheet.
• Fenders:  Extruded rolled aluminum.
• Bumpers:  Full width 3” molded rubber.
• Skid Plates:  (2) 3/16” formed aluminum.
• Paint:  Steel parts painted silver.
• Conspicuity Tape:  Meets all US and Canadian regulations.